Text Resize

-A +A
Bookmark and Share

Get a Subdivision Plat

Compass and Map Photo

How to Order

Applicants must provide the lot and square number(s) and a sketch of the provided layout of the lot(s) for the location where the subdivision is needed. If the subdivisions involves a tax (for example: 800 series numbers) then a deed will be required.

Cost

The cost for a subdivision plat is $440 for up to three lots. An additional fee may be required for subdivisions involving irregular-shaped lots.

Turnaround time

Approximate turnaround is four to six weeks.

Instructions for Handling and Executing Subdivision Plats

The plat of subdivision MUST be handled and executed as explained below, and returned to the Surveyor's Office for processing and recording.

Care and Handling of Plats

Do not fold, mutilate, alter, change, correct or add to this plat, and do not allow plat to get wet. Let the ink dry; do NOT smudge. If any of these occur, the plat will NOT be accepted for recordation and a new plat must be drawn at additional expense and time.

The ONLY types of pens and ink that can be used are:

  • Black ink ballpoint pens made by Cross, Skillcraft or equivalent.
  • Black permanent ink ULTRA FINE felt tip pens made by Sanford (Sharpie).
  • Black permanent ink drafting pens.

Owners

The owner(s) in fee simple of the property must sign the plat before a notary public and have two (2) witnesses for EACH signature. The owner(s) in fee simple executing the plat must remain the owner(s) in fee simple until the subdivision is recorded. If the owner is a corporation, the plat must be signed by two (2) officers, who are designated by the corporation charter or by the Board of Directors to act for the corporation. A Corporation seal is required. The corporation seals must be FIRMLY impressed to the plat and be LEGIBLE. Stick-on seals are unacceptable. If the owner is a partnership, the plat must be signed by a general partner.

Trusts

If there is a mortgage(s) on any of the property involved in the subdivision, the trustee(s) must sign the plat in the space provided. Indicate the number of trusts in the space provided. The trustee(s) signature(s) do not have to be witnessed or notarized.

Taxes

The applicant must take the plat to the Office of Tax and Revenue, Real Property Tax Administration, Customer Service Center, located at 1100 4th Street, SW, 3rd Floor, for certification as to the correctness of ownership shown on the plat and to verify that all current taxes and special assessments have been paid. When plats are to be recorded between April 1 and September 30, taxes must be paid through September 30; if recorded between October 1 and March 31, the taxes must be paid through March 31. Any questions regarding payment of taxes must be directed to the Office of Tax and Revenue at (202) 442-6696 or (202) 442-6790.

Historic Preservation Review

The plat is then taken to the Historic Preservation Division desk (#5) in the Permit Center located at 1100 4th Street, SW, 2nd Floor for review and sign off. ALL subdivision plats are to be taken to the Historic Preservation Division for a determination concerning the historic nature of the subdivision's location.

Zoning

The plat is then taken to the Office of the Zoning Administrator at 1100 4th Street SW, 3rd floor for certification as to compliance with Zoning Regulations. Note: The Office of the Zoning Administrator will hold the subdivision for review and signature by the Zoning Administrator. Upon signature, the Zoning Division will forward the subdivision to the Surveyor’s Office for final processing. Contact the Office of the Zoning Administrator at (202) 442-4576 to confirm delivery to the Surveyor’s Office.

Recordation

Upon receipt from Zoning, the subdivision will be reviewed, signed given a new lot number and record in the Office of the Surveyor within 3 business days.

The Zoning Administrator requires the following information in order to review and sign any subdivision plat for zoning compliance. The provisions of DCMR 10, Section 2703 require a preliminary sketch, drawn to scale and including but not limited to the following:

  1. Boundary of the land to be divided (Plat showing how the land is currently configured before subdivision);
  2. Provide a building location survey (Man made features, such as buildings, structures, walls, fences, culverts and sewers must be shown, be sure to indicate length and width dimensions, setbacks, and number of stories);
  3. If you are subdividing Assessment & Taxation lot(s), provide the date the lot(s) were created (Subdivision history).

When submitting the original Mylar plat for approval by the Zoning Administrator, the scaled sketch showing the above items must be provided with the subdivision plat.

Contact TTY: 
711